Leaderboard

Hmm, seems like someone had the issue before and a bodge was carried to rectify the issue (or at least attempt to rectify it). There is an issue with the timing chains and as far as I can see it was a recall from Nissan. It does suggest that it occurs on hard acceleration (e.g. from a slip-road) and if the chain is slack it can drift away from the timing point by a small fraction (much like a loose timing belt) which can then throw a code for cam/crank timing and result in what you are experiencing. I would personally replace the engine oil and look to see what has come out - e.g. metal particles and then replace it with the specified oil which may have not been supplied with previously. https://www.autodoc.co.uk/car-parts/engine-oil-12094/nissan/pulsar/pulsar-hatchback-c13/107484-1-2-dig-t If you use a quality oil of the correct specifications (as listed in the link above) and see if that makes any difference to how it runs. If no real difference is noted then I would advise to get the timing chain replaced which will almost certainly make a difference if it is worn

I use a smart screen with Android Auto. Then connect my phone via BlueTooth and use Waze map. Less expensive and live updates of accidents, traffic jams etc.

I had the same problem radio cutting off there is a fee upgrade from nissan now work perfectly it's a common problem

Hello, I am joining this forum with hopes to be able to supply you guys with some hard to come by parts for your beloved Nissans, as the title states we are the second oldest Nissan dealer in the uk and we are looking to move some of our older parts that have been stored away for years. I will be doing a follow up post with our parts list which should have thousands of items for you guys to sift through at your leisure, I just wanted to test the waters to see how helpful this would be for you guys, any responses or comments appreciated. Kind regards, Oscar

Hi all! Im thinking of getting a Pathfinder in the next month or two. Wanted something bigger for going fishing/camping and always loved the look of the Pathfinder. Especially the older shape (07/08 models). Has anyone got a rot free one with upgraded timing chain they are thinking of parting with? Thanks in advance 🤘🏻🙂 Harry

Thank you I will have a look and try that.

Hi Jeannie Does the sunroof sit and seal properly, no leaks? Open it right up and cleack for dirt, leaves, clean it out. Clean the rubber seals with a bit of wd40 or silicon just to make sure it sits properly. Also check the paintork to make sure the sunroof os not fowling the paintwork. May be touching as the car is flexing when moving. So, check there is no loose cabled, or anything dropped around the back, get a torch and take a look.

Hi Just bought a new Qashqai 1.3, and swapping out from a Volvo Xc40 In the Volvo I had capability to press two buttons on the steering wheel. This made the car recognise speed signs and keep the speed as per speed restrictions. Would not allow me to exceed the limit. Nice a simple. No concerns on unintentional speeding.. I was informed by Nissan sales my new car has this capability. So far struggling to figure how to do this assuming it can be done...Took a look on Google and found something's linked to TSR ICC and ProPilot. But unsure. So anyone in this forum, any idea what I am talking about and is it feasible.. appreciate any guidance.

UPDATE So it appears we may have FINALLY sorted this issue. It seems it was the suspension top mount. There was play in the mount as they showed me after they replaced it. So far so good, no noise. I will update further if it come back.

Yeah Trevor I generally get 3 months warranty out but with this being a newish car they gave 2 years for the price of 1

Nissan's local dealer sent me a email with the repair cost , they also found one of the springs had cracked and needed repairing which turned the cost up to £1294 luckily the warranty covers the cost

New to pathfinders. After doing some light modifications for a bit of off road use and was wondering what stealth winches people are using. Would like to keep the original bumper. Any guides about. Tia

I know... so nothing. But, Thanks.

Okey! I’ll try and see if it helps. Maybe with some cleaning additive in the fuel?

Thanks for the tip, I will check them out. Cheers.

When I had this i thought it was a phone or car setting. Can't really remember but I did get it to stop by altering which ever setting it was.

Hey guys, not sure if this is the right place to post "for sale". Sorry about that. I'm selling my 1 owner Pathfinder SE. 70,125 miles. Engine and trans in perfect running condition. Does need a SAS and flex plate. I have all service/oil change receipts. Asking $4500 neg.

Exact same thing just happened to me this weekend, car just stopped with no warning! I'm going to try and claim through my finance company claiming a breach of my consumer rights but i'm not hopeful. Looking online it seems the problem is endemic!

Hi everyone, I am Sid and I own a 1993 K reg 1.6 Sunny SR. Looking for a few bits and bobs and hopefully good advise. Thanks All.

thanks admin. I'll take some pics, and post later. Any views on the 1.2 engines?

Hi Sappo, I took delivery of my Juke Hybrid in December, so now have three months experience with it. My primary reason for changing was the Juke's higher ride - I previously had three Toyota Hybrids (Auris and Corolla) and was starting to struggle getting in and out due to a back problem. To that end the Juke has been a 100% improvement. However, for my money the Toyota Hybrid system is far superior. I could easily exceed 60mpg with the Toyotas without making any adjustments. Best I have achieved so far with the Juke is 52 - that is using Eco Drive and e-pedal, both of which have to be activated every time I start up. I have no mechanical expertise but I cannot understand why the Juke revs so high when travelling between 28-31, which for most of us is the speed we drive at around town. That said, I find the car has a very solid feel (maybe a more "robust" ride than the Toyota) and I feel safe in it. Psalmist

Hi Paul, thanks for reply. the files are mp3, so should all play. I am using a one of the newer sticks, USB-C, in case older sticks don’t work on the latest latest players. So everything is compatible. i will up date this saga after the visit to the dealer who is going to check player in the car.

It should be something like selecting the individual seat position and then depressing the position number 1 or 2 button (depending on who is driving at the time) for a short period of time

Thanks for that Trevor. I have now stripped it all down to basics and confirmed that: there is definitely full voltage on some of the connector pins, that the linkages are moving nicely (a touch of oil helped) and the motor is not interested in doing anything (not even with the linkages disconnected). I have now ordered a motor which I should get by Sunday.... I will let you know how it goes. Many thanks, Dave

It sounds like battery strength and condition is poor. I would definitely try a new battery before proceeding to replace other parts

Thanks - I got a new primer pump and it didn't help at all. I could try a new filter, but I did change that one recently.

Hi All Just introducing myself. I have owned my 2005 350Z Roadster for circa 10 years now and enjoyed it. My other automotive hobby being a Megapin single seater circuit race car which I am rebuilding as it has been garaged by the previous owner for several years. I am replacing the engine and all the fibreglass parts with carbon fibre which has taken me circa 3-4 years to perfect. So I now offer carbon fibre parts like aero boot wings etc My 350Z has lots of parts during my ownership including a Jap speed K4 cat back exhaust, Mohair soft top, lots of bracing and I am about to replace the throttle body for the 75mm offering, I just need to machine the fitting plate and make a 75mm carbon fibre inlet pipe. In my early days of ownership like lots of other owners experienced the knock from the front suspension so replaced the shocks & springs then found out it was the Barings in the banana arm Dhoh. Thats reminds me I still have the original shocks and springs lol Anyway I hope to be posting some of my experiences with the car and I'm happy to help anyone thats encounters anything I have experience with. Cheers Chris

You can get a stainless steel one custom made for not a lot of money....check on eBay for sellers https://www.ebay.co.uk/sch/i.html?_from=R40&_trksid=p2499334.m570.l1313&_nkw=+nissan+juke+nismo+rear+silencer&_sacat=131090

Hi...welcome to the Club Can't go too wrong with a Micra. Simple engineering and go on for years Good to have you onboard!

I would like to replace the head unit on my Maxima, in particular to get a functioning integrated satnav. I could do with a recommendation based on experience from a J12 owner. By way of introduction, I am in my seventies and retired as a Postman. First Nissan (Datsun), was a 120Y Coupe (my wife's) on which she traded a 72 Torana. After that, 180B wagon, 200B Wagon, N10 Pulsar (first model 5 speed manual dealer rep {my neighbor} car, Skyline Exec, 260C 280C (one of those was a wagon ?) 2002 Maxima 320k J12 2012 Maxima (written off for me) J12 2012 Maxima replacement. I also had a Bluebird as a company car, part of a small fleet I bought for the company I worked for. Main interest in motoring is BSA/Triumph bikes.

Will check Will check

Hi, same issue I had. Battery is fully charged. All the lights were on but not starting. I found this in another forum I followed the advice and I worked. Hope it’ll help 🙂 Thanks Jackyboy117’s advise : ‘I turned the ignition switch to the second point just before you start the engine, I then got out the car and disconnected the negative lead and replaced straight away. Now the car started to try and start but would only make the noise. I then had to shut all doors and bonnets, turn the engine off, lock the car with the key, open the car with the key, half turn the ignition and leave for 5 mins. Once the 5 mins is up turn off the car and straight away start.’

Samco are a company that specialise in Silicon hoses so they can provide different diameters and lengths and you can also get couplings and adapters to make up your own hoses

Will do I’m booked in for next Tuesday.

For sale Nissan D21 stoke on Trent

Nissan fixed it under warranty.

Hi, new to forum. I've just bought a 72 plate nsport and am wondering if anyone can suggest a reliable wireless phone charger that works with an android phone and fits nice in front of the changer where the USB slot is Thanks in advance

That's great thank you for that.

Hi Trevor, thanks for your response! That gives me a bit more confidence that its just going to be a bit of a learning curve

Hi Jon....welcome to the Club Good to have you onboard!

Yes Trevor we will there is a place and they have different lengths I'll find the web site over weekend

You should ideally change both at same time given they’re both the same age and done the same mileage.

Hi, what codes showed up when you had it checked? I’m sure you can’t just purchase the regulator as it is inbuilt into the fuel pump on the 1.5 k9k engine so you would have to fork out for the lot

Hi just thought I’d introduce myself, I’m Steve from the north east of England. I have recently pruchased a Nissan sunny coupe 1.6 GSX 1990. I work at Nissan as well as a panel repairer. nice to meet you all 😊

I have purchased a 1991 Nissan Vanette. I just wondered if there were any other owners?

Probably more economical as well Maybe worthwhile looking through Autocar reviews on both models to see how they fair in a road test

Hi guys I'm new to the group hoping to buy a 2018 nissan micra 1.5dci with 18k on the clock... im abit unsure if I should buy it as I only seem to find negative reviews. I was wondering if anyone had any positive experiences with the micra. How reliable are they? What are the common faults etc... Any help would be greatly appreciated Thanks Luke

Sadly not! We had to pay the cost of replacement Clutch of £1800 plus an AA report of £200. The AA sent ACE (Automotive Consulting Engineers Ltd) to carry out the inspection which concluded that the Clutch had over heated which caused the failure. No suggestion as to cause other than abuse and referred to Towing in the report which did not mention that there is not a Tow Bar on the car! The report appeared to me to have a large element of "cut and paste" about it. I tried to contact ACE for more details of the inspection but they did not respond I contacted Nissan and asked if they could Inspect the components and the Dual Mass Fly Wheel, they declined and suggested I look on the Internet to find someone to inspect it but could not suggest anyone. The Nissan "Adviser" declined to discuss the matter any further with me and refused to put through to a Manager. We reject the suggestion that we "ride" the clutch as there is adequate spec by the clutch pedal to rest the foot and we have suddenly become bad drivers. I took legal advise and my Solicitor advised that we could become involved in a costly dispute. We are left with a car that my wife is reluctant to drive as she has lost faith in it. We ask ourselves three questions. Would we buy another Nissan, would we recommend a friend to buy a Nissan and are we satisfied with Nissan's Customer Care? NO, NO, ABSOLUTELY NOT.

Nissan Micra K12 Throttle Body Removal and Clean Welcome to this guide on how to remove and clean the throttle body on a Nissan Micra K12. This procedure was done on a 1.2 2003 petrol model. As I couldn't find a good tutorial on this process I thought I would have a go myself and then put together this guide for other people. The process is actually relatively straight forward once you know how. I was experiencing juddering at certain points on the rev range and when the car was in a certain gear, MPG had decreased plus some hunting when the car was idle. So I decided that I would clean the throttle body to see if that would help. I actually didn't know exactly where the throttle body was located on this model. It's actually located under the air intake box/top manifolds which are shown below. It's actually located inside and under the top of the plastic manifold housing. Once you have removed the throttle body you will realise that it's actually connected to one of the electrical connections on the top of the housing that you will need to disconnect as part of this process. Throttle body location This is where the throttle body is location on a 2003 1.2 petrol Nissan Micra K12. Tools required This is a list of tools and other items required to get to the throttle body, remove it from the housing and then clean it: Pliers or grips 10 mm socket Ratchet Toothbrush or cotton buds and an old but clean cloth A good carb/throttle body cleaner The process So here are the steps. Step 1 - Remove the air intake and air filter box Remove the air intake pipe (highlighted by the red arrow) by removing the plastic lugs that hold it to the front of the engine bay and then remove the other end from the air filter housing on the right. I had to slightly twist mine and then gave it a hard pull to detach it. Then remove the air filter housing from the manifold housing. Do this by unclipping the metal retaining clips (highlighted in blue in the image below) located on the front and the right side of the housing. There are only two clips that hold this in place. They simply unclip upwards and one remains connected to the top housing and the other remains connected to the air filter box. Once you have unclipped the air filter housing the front of it may drop away from you. It should not fall off completely as the back is held in place by the box being slid into holders in the back of the top housing. To remove the air filter box simply push the front down and when it's at a certain point pull the air filter housing towards you. This will pull it out of the rear mounts. Try to look at the rears mounts when you do this so that you can be sure you pushed it down enough to be able to pull it forward without snapping the plastic mounts on the back of the top housing. You should see this when the air filter housing has been dropped away from the top housing. The air filter itself may have stuck to the underside of the top housing like mine did so just pull it off and place to one side. I would suggest replacing it with a new filter whilst you are doing this as you will have to put it back in when you reassemble. Now just slide the air filter housing out of the engine bay so that you can continue. You will see this. Step 2 - Disconnect Electrical Connectors Disconnect the three electrical connectors as highlighted in red. The one to the left of the top housing is the actual throttle body connector. Once the one in the middle of the top housing is unplugged, make sure you gentle pull it out of the recess that the rest of the cable lies within and gently push it to one side out of the way. Do not just pull these connectors as they are made from plastic and will snap. They all have a small tab which needs to be depressed at the same time as gently pulling them. Do not pull them too hard as they do not need it. They will disconnect very easily if the tab is pressed whilst pulling them. Step 3 - Disconnect Breather Pipes/Hoses Disconnect the two breather hoses/pipes as highlighted in red. You will need to use a pair of pliers to release the retaining clips that hold the end of the pipes tightly sealed in place. Just squeeze the release arms on the retaining clips with the pliers and slide the retaining clips along the pipes until they are free of the housing connector. Now just gentle pull the hoses/pipes off the housing connectors. Again, you do not need to pull these hard. They should just slide off with a light pressure. Remove the centre hose from the recess in the top housing and push it out of the way. You should now see something like the image below. All electrical connectors have been disconnected and the hoses disconnected. I took this picture before I had moved the centre hose out of the way so you shouldn't have this in place at this stage. Next remove the breather hose mount, shown below, from the top housing. If you don't remove this you will not be able to remove the top housing completely if you leave the rear hose attached. Alternatively, you could leave it bolted on and just remove the other hose from it and then remove the top housing with the mount attached. I just unbolted it and pushed it out of the way so I didn't damage it. Once you've removed the mount then it should look like the image below. Just move it gently out of the way so that it doesn't interfere when you remove the top housing. Step 4 - Remove Top Housing You can now remove the top housing by simply removing the bolts highlighted in red in the below images. They are all 10 mm. Remove the three front bolts. Remove the two bolts on the left rear of the housing. Remove the two bolts on the right rear of the housing. Once the seven bolts have been removed you can simply pull the top of the housing up towards you and it should separate from the bottom section of the housing. Warning: Do not pull this top section up too hard. You should be able to just pull it up with a little force. The top section is attached to plastic manifold inlet pipes toward the rear and they are pretty much held on by O rings. Try to pull the top section of the housing up towards you in a straight motion. Try not to bend it as you pull it up. It should come off fairly easily. Warning: This top section actually contains the throttle body itself so take care. Do not just drop it to one side as you may damage the throttle body that you are about to clean - if you are not replacing the throttle body itself of course. You should now see the image below once the top section is removed. Step 5 - Remove Throttle Body From Top Housing Once you've pulled off the top housing turn it over to see the location of the throttle body. Simply remove the three bolts that are highlighted in red in the image below. They are 10mm so just use the same socket you used to remove the top housing bolts. Once you have removed the three bolts you can now remove the whole throttle body. The throttle body is now only held in by the top of the electrical connector on the outside of the top housing. It's a bit tight so just pull the throttle body towards you whilst wiggling it slightly as the rubber seal is a little tight. Don't put too much force as you might snap the plastic top housing. You should now see the housing like this once the throttle body has been removed. Step 6 - Clean The Throttle Body To clean the throttle body I used a small headed toothbrush, some clean rag and a good carb / throttle body cleaner. Warning: Carefully follow the instructions on the carb cleaner. Do this work in a well ventilated area, preferably outside and wear a suitable breathing mask. Take extreme care not to inhale the fumes from this cleaner or the dirt that it removes from the throttle body. I used the following carb cleaner which is available from a well known parts store for about £8. This was the state of my throttle body when I got it out. It was really clogged up and clearly sticking. Simply attach the small pipe to the can of carb cleaner and then spray into and around the inside of the intake of the throttle body and all over the butterfly valve. Then just brush the whole of the inside of the intake (front and back) and butterfly valve with the toothbrush and/or rag. The dirt should come off quite easily as the carb cleaner is really effective. Keep doing this until the intake and butterfly valve are as clean as you can get them. Keep wiping off any residue with a good clean rag as well as you do this. After about 10 minutes of cleaning I had a nice clean throttle body as shown below. Yours should look pretty similar when complete. Step 7 - Refit Your Throttle Body And Reassemble Other Parts Warning: Before refitting your cleaned throttle body you should ensure that the throttle body is dry and does not contain any residue from the cleaning agent. I left my throttle body to completely dry for about an hour or so just to be extra cautious before proceeding with refitting. Refitting your throttle body and reassembly is just really this guide in reverse from step 5 back to step 1. Warning: Take care when reattaching the top of the housing to the bottom and the intake pipes as they have O rings present. Ensure that they are correctly aligned before pushing the top housing down into place. Be careful not to pinch or tear the O rings. If it's tight to refit over the O rings then either replace the O rings or simply apply a small smear of engine oil around the O rings which should help refit the top housing. Warning: Do not over tighten the bolts that hold the throttle body in place or the top housing. Warning: Once you have reassembled everything it is a good idea to just double check that all the breather hoses are reattached and secured in place and that all the electrical connectors are attached securely. You should now be able to start the car and test accordingly. If this process has been successful then you should have a smoother throttle response and possibly more accurate. Mine stopped juddering at certain revs and seemed so much more responsive. I am also now getting much better fuel economy.